Wall Mounted 180 Degree Detection Infared Motion Sensor Swtich

Welcome to use GST08 infrared motion sensor!
The product adopts good sensitivity detector, integrated circuit. It gathers automatism, convenience, safety, saving-energy and practicality functions. The wide detection field consists of up and down, left and right service field. It works by receiving human motion infrared rays. When one enters the detection field, it can start the load at once and identify automatically day and night; its installation is very convenient and its using is very wide. It has functions of power indication and the detection indication.
SPECIFICATION:
Power Source: 220V-240V/AC                   Detection Range: 180°
Power Frequency: 50Hz                        Working Temperature: -20~+40ºC
Ambient Light: 3-2000LUX (Adjustable)           Working Humidity: <93%RH
Time-Delay: min: 10sec±3sec                  Installation Height: 1.8m~2.5m
            max: 8min±2min                  Power Consumption 0.45W (work)
Rated Load: 800W (incandescent lamp)                           0.1W (static)
200W (energy-saving lamp)         Detection Moving Speed: 0.6~1.5m/s
Detection Distance: 12m max(<24ºC)
FUNCTION:Can identify day and night: The consumer can adjust work ambient light. It can work in the daytime and at night when it is adjusted on the "sun" position (max). It can work in the ambient light less than 3LUX when it is adjusted on the "moon" position (min). As for the adjustment pattern, please refer to the testing pattern. Time-Delay is added continually: When it receives the second induction signals after the first induction, it will compute time once more on the basic of the first time-delay rest (Set time).Time-Delay is adjustable. It can be set according to the consumer's desire. The minimum time is 10sec±3sec. The maximum is 8min±2min.
INSTALLATION (see the diagram)
< >Switch off the power.Screw off the nail on the bottom. Open the wire hole. The power wire and the load wire are bored in the bottom. Fix the bottom on the selected position with the inflated screw.Connect the power and the load with the connection-wire column according to the sketch diagram.Fix the sensor on the bottom, please screw the nail and switch on the power. So you can test it.CONNECTION-WIRE DIAGRAM
 
 
TEST:
< >Turn the time knob clockwise on the minimum (-), turn the LUX knob clockwise on the maximum (sun).Switch on the power, the load doesn't work and the indicator lamp doesn't work. Warm-up 30sec later, the indicator lamp is turned on at the same time, under the conditions of no sense signal, the load should stop working within 5~10sec and the indicator lamp is turned off.After the first is out, make it sense again after 5~10sec. The load should work. The load should stop working within 5~15sec when no any sense signal.Turn LUX knob anti-clockwise on the minimum. If it is adjusted in the less than 3LUX, the inductor load should not work after load stop working. If you cover the detection window with the opaque objects (towel etc), the load work .under no induction signal condition, the load should stop working within 5~15sec.
Note: when testing in daylight, please turn LUX knob to     (SUN) position, otherwise the sensor lamp could not work!

NOTE:
< >Should be installed by electrician or experienced person.There should be no hindrance and moving objects in front of the detection windows to effect detection.Avoid installing it near air temperature alteration zones such as air condition, central heating, etc.Considering your safety, please do not open the cover when you find the hitch after installation.If there is difference between instruction and the function the product has, please give priority to product and sorry not to inform you additionally.SOME PROBLEM AND SOLVED WAY:
< >The load do not work:a. Please check if the connection-wiring of power and load is correct.
b. Please check if the load is good.
c. Please check if the working light sets correspond to ambient light.
< >The sensitivity is poor:a. Please check if there has hindered in front of the detection window to effect to receive the signal.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection fields.
d. Please check if the installation height corresponds to the height showed in the instruction.
e. Please check if the moving orientation is correct.
< >The sensor can not shut off the load automatically:a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is the longest.
c. Please check if the power corresponds to the instruction.
d. Please check if the temperature near the sensor changes obviously, such as air condition or central heating etc.